Opening overview
When crafters compare Let’s Resin vs Puduo UV resin, they’re usually weighing two popular mid-viscosity, UV-curable systems that have become staples for small-batch jewelry. Both brands are widely available in the budget to mid-range price bands, and both cure under 365–405 nm LED lamps. Because neither manufacturer publishes full technical data sheets, this guide relies only on the specifications we can confirm from retail listings and SDS excerpts. If you need fully documented materials, consider our epoxy resin roundup instead.
Disclosure / Werbung: This page contains affiliate links. If you buy through our links, we may earn a commission at no extra cost to you — this helps keep ResinBench free. (Dieser Beitrag enthält Affiliate-Links / Werbelinks.)
Core concepts with specs from PRODUCT_DATA
Both Let’s Resin and Puduo UV resins are one-part, solvent-free acrylate oligomers that polymerize under UV-A light. Retail listings indicate they are supplied in 100 g, 250 g, and 500 g bottles, with working times (open time before gel) of roughly 10–15 minutes under typical workshop lighting. Post-cure hardness is not specified by manufacturer, but user reports commonly cite Shore D 75–80 after a full 24-hour post-cure in sunlight or a dedicated UV chamber.
Viscosity for both resins is described by sellers as “medium” or “syrup-like,” which in practice means they self-level in molds up to about 5 mm deep without vacuum degassing, yet still hold fine details such as lace or tiny flower petals. Color stability is rated as “good” for indoor use; prolonged outdoor UV exposure will yellow both brands equally.
Project-outcome mapping
| Project type | Let’s Resin | Puduo UV Resin |
|---|---|---|
| Thin-layer jewelry (pendants, earrings ≤ 3 mm) | Excellent clarity, minimal bubbles | Slightly faster surface cure; same clarity |
| Resin charms with embedded dried flowers | Good; petals stay suspended | Good; slightly higher viscosity can trap air around edges |
| Coating paper or wood for decoupage | Thin, even spread; gloss finish | Same; may require sanding between coats for perfect leveling |
| Deep pours (> 10 mm) | Not recommended; heat spike can cause cracking | Not recommended; same limitation |
| Flexible pieces (bangle bracelets) | Not specified by manufacturer | Not specified by manufacturer |
In short, for most small-batch jewelry work under 5 mm thickness, Let’s Resin vs Puduo UV resin is a toss-up; the choice often comes down to local availability and color palette rather than performance.
Practical guidance / how-to
- Prep: Warm both resin and hardener (if applicable) to 25–30 °C to reduce viscosity and bubble count. Neither brand lists a mandatory pre-heat step, but it improves flow.
- Mixing: Both are single-part, so no mixing ratio is required. Shake the bottle gently for 30 seconds to re-homogenize any settled additives.
- Pouring: Use a slow pour from 5–10 cm height to minimize air entrainment. A toothpick or silicone tool can pop surface bubbles before curing.
- Curing: Use a 365 nm or 405 nm LED lamp rated at ≥ 12 W. Cure thin layers (≤ 2 mm) for 2–3 minutes; thicker layers may need 5–6 minutes per side. Post-cure under sunlight or a UV chamber for 24 hours to reach full hardness.
- Finishing: Lightly sand with 800-1000 grit wet/dry paper to remove nibs, then polish with a microfiber cloth and a drop of resin for a glass-like finish.
Troubleshooting
- Sticky surface after full cure: Usually indicates under-cure. Re-expose under the lamp for an additional 3–5 minutes, then post-cure in sunlight. If the piece is thicker than 5 mm, consider curing in layers.
- Cloudiness or fogging: Can be caused by moisture contamination or insufficient mixing of pigment pastes. Ensure your workspace humidity is below 60 % and that any colorants are fully incorporated.
- Bubbles: Common with medium-viscosity resins. Warm the resin slightly, pour slowly, and use a heat gun on low setting (10–15 cm away) to pop bubbles before gel stage.
- Yellowing over time: Both resins will amber slightly with UV exposure. To slow this, store finished pieces away from direct sunlight and consider a clear UV-resistant topcoat.
Buyer guidance
If you are deciding between Let’s Resin vs Puduo UV resin, start with the smallest bottle (100 g) from each brand to test color, cure speed, and compatibility with your pigments. Both are readily available in the budget price band, so cost is rarely the deciding factor. Check the color range—Let’s Resin often offers more pastel and iridescent options, while Puduo leans toward vibrant neons. If you need documented food-safe or medical-grade certifications, neither brand provides them; switch to a dedicated bio-based epoxy instead.
Finally, for larger projects or deep pours, consider stepping up to a two-part epoxy system with a longer pot life and lower exotherm. Our deep-pour resin guide covers options that are better suited for river tables and thick molds.